Course detail

Electronics and Measurement

FSI-ZEMAcad. year: 2009/2010

The course "Electronics and Measurement" familiarises students with procedures and principles of technical experiment in work of a mechanical engineer. It defines the basics of the modern methods applied for measuring of mechanical quantities, and explains the structure of the measuring and control chain. The course deals with the analysis of the analog and digital signals in time and frequency domain too. A part of the course is also devoted to the measurement of kinematic quantities, forces, torques, pressure and noise. The course is divided into the following blocks: acoustic measurements in engineering, basics of experimental modal analysis, monitoring of a technical machine condition and service life tests of mechanical units.

Language of instruction

Czech

Number of ECTS credits

2

Mode of study

Not applicable.

Guarantor

doc. Ing. Ivan Mazůrek, CSc.

Department

Institute of Machine and Industrial Design (ÚK)

Learning outcomes of the course unit

Students will have an overview of contemporary possibilities of experimental detection of some mechanical quantities needed for an assessment of failure-free operation of machines and their parts. They will be provided with fundamental practical knowledge of and experience with these problems. They will be able to formulate real requests for these activities and will have a grasp of evaluation and interpretation of the results.

Prerequisites

Basic knowledge of mathematics, numerical mathematics, statistics and probability, physics, mechanics and electrical engineering.

Co-requisites

Not applicable.

Planned learning activities and teaching methods

Teaching methods depend on the type of course unit as specified in the article 7 of BUT Rules for Studies and Examinations.

Assesment methods and criteria linked to learning outcomes

Course-unit credit is awarded on the following conditions: - active participation in the seminars, - good results of elaborated laboratory exercises, - solution of additional tasks in case of longer excusable absence. Examination – combined (written and oral). In the written part the student has to prove knowledge of basic terms, important principles and their application; the oral part takes the form of a discussion over the written part and records from laboratory exercises.

Course curriculum

Not applicable.

Work placements

Not applicable.

Aims

Students will acquire theoretical and practical knowledge of and experience with contemporary methods, experimental instrumentation and computer technology intended for detection of input data, for computational simulation of machines and machine parts, as well as for verification of results. Also dealt with are kinematic quantities, forces, moments, pressures and noise and processing of acquired results with using of CAT/CAME systems.

Specification of controlled education, way of implementation and compensation for absences

Attendance at practicals is required. One absence can be compensated for by attending a seminar with another study group in the same week, or by elaboration of substitute tasks. Longer absence may be compensated for by special tasks according to instructions of the tutor.

Recommended optional programme components

Not applicable.

Prerequisites and corequisites

Not applicable.

Basic literature

Not applicable.

Recommended reading

Not applicable.

Classification of course in study plans

  • Programme M2I-P Master's

    branch M-KSI , 1. year of study, winter semester, compulsory

Type of course unit

 

Lecture

26 hours, optionally

Teacher / Lecturer

doc. Ing. Ivan Mazůrek, CSc.

Syllabus

1. Fundamentals of experimentation theory
2. Measurement of non-electric quantities
3. Processing of a measured signal
4. A/D converter
5. Time domain analyses of a signal
6. Frequency domain analyses of a signal
7. Problems of using of DFT
8. CAT/CAME systems
9. Measurement system IEEE488 (IMS-2, GP-IB)
10. Measurement system software
11. Acoustic measurement in engineering
12. Experimental modal analyses
13. Monitoring of machinery condition
13b. Working life tests of complicated machine units

Computer-assisted exercise

26 hours, compulsory

Teacher / Lecturer

doc. Ing. Milan Klapka, Ph.D.
doc. Ing. Ivan Mazůrek, CSc.

Syllabus

1. Workplace safety in the laboratory, demonstration of selected laboratory tests
2. Demonstration of selected laboratory tests
3. Transducers of physical quantities
4. Calibration of accelerometers and microphones
5. Problems of utilisation of DFT
6. Problems of utilisation of DFT
7. Digital filtration of signal
8. Digital filtration of signal
9. Specific instruments of LabVIEW
10. Programming of measuring application with LabVIEW
11. Acoustic measuring in a free field, colour of sound
12. Acoustic measuring - colour of sound
13. Experimental estimation of modal parameters of a fixed beam
13b. Credit test