Czech

Not applicable.

The ability to design the technologic sequences by joining of unit operation, to form a point of view of ordination of technological lines and receive a concrete knowledges of plastic processing

Physical chemistry. physics of polymers
Macromolecular chemistry
Stabilisation and additivation of polymers

Not applicable.

Teaching methods depend on the type of course unit as specified in the article 7 of BUT Rules for Studies and Examinations.

Oral exam
- quetions according themes of lectures
- advisement in way of possible processing of concrete plastic part

Basic therms and splitting of plastics - deformational behiour, terminology of polymers, thermomechanical curve, behaviour of plastic melts, additives its influence on processing
Rheology of plastic melts - basic mechanic of flux, rheology by processing, shear viscosity - temperature and prssure dependency, affect of MW and additives on viscosity, rheometry of polymers - extrude, planparalel and rotational plastometres, normal a shear stress by flux, normal viscosity and its phenomens
Energy by processing - heating and cooling, types of heaters, principes of cooling, pressed air, enerfy for polymer modification - mechanical, thermic and radiatic, energy balance of processes
Haldling and prepare processing of polymer materials - basics of drying, milling, dissolving a dispergation, transport and storing of raw materials, colouring, preparing of blends - mixing and kneating, machines, mechanism of mixture formation, tabletation and pelletising, lines of preprocessing, grinding and processing of plasic scraps
Calendering - solid and viscous material between rolls, rates and pressure profile, dissapative output, temperature field, kneating on double calender, types of calenders a its use (construction of calenders), calender lines
Extrusion - function of screw, entering zone - friction output, middle and exit zone, time of residence, kneating output, types of screws, dies, dynamic od process, technology with extrusion
Cyclic processing ways
Molding and fluxmolding - presses, ways of power affects, presses for laminates, floor presses for sheets, rotational presses
Moulds - main parts, terminology by hole numbers, by construction, by overflux, removing of products out of moulds, heating, technology of moulding
Injection moulding - machines, plastification and injection unit, clamping unit, engine and control
Injection moulds - design of multiply, influx systems, disaerating, basic principe of removing, temperation of moulds, principes of design of products
Technology of injection - cycle, relations in mould, influence of technological parameters,
processing of filled thermoplastics, structural foams, thermosetics, morecomponent injection, sandwiches, possible trouble
Blow moulding - extrusion and injection way, blow with orientation
Foaming - factors and processes - surface stress, dissolving, nucleation
Thermoforming - ability of semifinished products, machines, technology, comparing to injection moulding
Rotational moulding - materials, cycles, relations in mould
Processing of fluid systems - dispersions - casting and coating
Reatiction moulding - low- and high pressure way, structural foams
Processing of fiber laminates - discontinual and continual
Spinning - principes, modification of fibres
Fastening - mechanical joint, bonding and adhesives, prepating of surfaces, coating, formation on bond, types of adhesives, sheet backing
Welding - contact, by additional material, by high frequency, by ultrasound, frictionaly, by radiation
Surface finishing - painting and printing, patterning, glossing and metallising, preservation by powder plastics, velvet finishing

Not applicable.

The subject of the lecture-course is given to apprise the students with several types of polymer processing in the relation to basic material properties. The target of course is a realtion between
processing – structure of polymer for particular types of proceeding a ability to define material requirement for given technology on engineer principle.

Attendancy in lecture is recomended. Student prepare presentation focused on actual technology. To do it, student have recomendeed literature and regular consultations.

Not applicable.

Not applicable.

Kuta A.: Technologie a zařízení pro zpracování kaučuků a plastů, VŠCHT Praha, Praha 1999. (CS)
Štěpek J., Zelinger J.,Kuta A.: Technologie zpracování a vlastnosti plastů. SNTL Praha, Praha 1989. (CS)

Ducháček V.: Polymery - výroba, vlastnosti, zpracování, použití. VŠCHT v Praze, Praha 2006. (CS)
Charrier J. - M.: Polymeric Materials and Processing. Hanser Publishers, New York 1990. (CS)
Tomis F.: Gumárenská a plastikářská technologie. Zpracovatelské procesy. VUT v Brně, Brno 1987. (CS)