Course detail

Special Technology of Forming Metals

FSI-HSTAcad. year: 2011/2012

Special and unconvencional methods of sheet metal forming, forging resp bulk forming. Processes analysis, infuence of forming conditions and parameters, forming limits with respect of defects and forces. Technological sketches of methods.Applications.

Language of instruction

Czech

Number of ECTS credits

6

Mode of study

Not applicable.

Guarantor

prof. Ing. Radko Samek, CSc.

Department

Institute of Manufacturing Technology (ÚST)

Learning outcomes of the course unit

The students will acquire knowledge of conventional as well as unconventional types of technologies, and will be able to apply these technologies for particular cases of forming.

Prerequisites

Knowledge of technological courses IV. year of study.

Co-requisites

Not applicable.

Planned learning activities and teaching methods

Teaching methods depend on the type of course unit as specified in the article 7 of BUT Rules for Studies and Examinations.

Assesment methods and criteria linked to learning outcomes

Course - unit credit requirements: participation in the exercises, delivery of assigned papers.
The examination consists of written and oral part. The final classification will be in accordance with the article No. 13 of the Rules for Studies and Examinations valid at the Brno University of Technology since 2004/2005.

Course curriculum

Not applicable.

Work placements

Not applicable.

Aims

The aim of the course is to familiarise students with the use of special forming methods in broad terms.

Specification of controlled education, way of implementation and compensation for absences

Missed lessons will be compensated in alternative exercises by arrangement with the teacher.

Recommended optional programme components

Not applicable.

Prerequisites and corequisites

Not applicable.

Basic literature

MIELNIK, Edward M. Metalworking science and engineering. New York: McGraw-Hill, c1991. ISBN 00-704-1904-3. (EN)
SAMEK, Radko. Vybrané statě z teorie a technologie tváření v letecké výrobě: Technologie výroby dílců draku objemovým tvářením za tepla. Vyd. 1. Brno: RVO VA AZ, 1989. (CS)
ŽÁK, Jan; SAMEK, Radko a BUMBÁLEK, Bohumil. Speciální letecké technologie I. Praha: Mezinárodní organizace novinářů, 1990. Učební texty vysokých škol. ISBN 80-214-0128-1. (CS)

Recommended reading

DVOŘÁK, Milan, František GAJDOŠ a Karel NOVOTNÝ. Technologie tváření: Plošné a objemové tváření. 2. vyd. Brno: Akademické vydavatelství CERM, s. r. o., 2007. ISBN 978-80-214-3425-7.
ŽÁK, Jan, Radko SAMEK a Bohumil BUMBÁLEK. Speciální letecké technologie I. 1. vyd. Ediční středisko VUT Brno. Brno: Rektorát Vysokého učení technického v Brně, 1990. 220 s. ISBN 80-214-0128-1.

Classification of course in study plans

  • Programme N2301-2 Master's

    branch M-STM , 2 year of study, winter semester, compulsory-optional
    branch M-STG , 2 year of study, winter semester, compulsory-optional

Type of course unit

 

Lecture

26 hod., optionally

Teacher / Lecturer

prof. Ing. Radko Samek, CSc.
doc. Ing. Milan Dvořák, CSc.
Ing. Eva Peterková, Ph.D.
doc. Ing. Zdeněk Lidmila, CSc.

Syllabus

1. Formability and forming limit diagrams in special technologies
2. Stretch formig of sheet panels and profiles( bending with tention force)
3. Bulge forming by rigid and non rigid tools
4. Power spinning processes in cold and heated conditions
5. High energy rate forming processes
6. Problems of forming and forging of AL and Ti alloys
7. Ring rolling ( hot and cold processes)
8. Precission and orbital forging
9. Superplastic and isothermical forming and forging
10.Special methods of bulk cold forming(grooves and gear worm rolling,shot peening... )
11.Special methods of drawing ( differential heatig, opposite force,wall-reduction..)
12.Special methods of tube forming
13.Tribology problems in sheet metal forming