English

Not applicable.

Student, who passed the course, is able:
- to distinguish basic types of binary signals, to compute and draw their spectra and describe principles and characteristics of the most widely used line codes,
- to list individual blocks of the digital communication system and explain their functions,
- to describe additive white Gaussian noise (AWGN) channel model, to define bit error rate, to compute probability of error reception in case of both baseband and passband binary signal transmission affected by AWGN,
- to describe principles, to define parameters and to list characteristics of basic and modern modulation methods,
- to explain the cause of intersymbol interferences (ISI) and Nyquist strategy of zero ISI in sampling moments, to draw and describe impulse responses of both raised cosine and Gaussian shaping filters,
- to describe the principle of channel equalization, to explain operations of adaptive equalizer and decision feedback equalizer,
- to explain the principle and importance of synchronization in the communication system, to explain the purpose of scrambling, to design the block diagram of a simple self-synchronizing scrambler,
- to describe principles of the automatic repeat request (ARQ) and the forward error correction (FEC), to explain the principle of interleaving, to describe methods of block and convolutional interleaving,
- to explain the difference between natural and uniform methods of sampling, the cause of aperture distortion and methods of its suppression,
- to describe principles of the pulse width modulation (PWM), the pulse position modulation (PPM) and the pulse density modulation (PDM),
- to explain the difference between uniform and non-uniform methods of quantization, to compute the power of the quantization noise, to draw the graphs of compressor and expander transfer functions,
- to describe principles and to list basic characteristics of pulse coded modulations (PCM, DPCM, DM, ADM, SDM),
- to explain principles of basic methods of signal multiplexing and multiple access,
- to describe and design the orthogonal frequency division multiplex (OFDM), to define its basic parameters and to list its typical characteristics and examples of application,
- to describe basic types of intensity modulations of light used in optoelectronics,
- to define and compute basic quantities used in the information theory (self-information, entropy, redundancy, mutual information, channel capacity), to explain the principle of the trellis coded modulation (TCM).

Student, who enrolls for the course, should know basic definitions and characteristics of signals and systems with both continuous and discrete time, including their mathematical description and representation in the frequency domain, and also know basic types of probability density and distribution functions and have knowledge of the signal sampling and filtration. It is also assumed that student can compute the derivative and integral of a function, modify equations with logarithms, complex numbers and trigonometric functions, solve linear equations and use the MATLAB software. In general, the bachelor level knowledge from the area of mathematics and physicsl and general English language competence are required.

Not applicable.

During the lectures, the theory is explained with the aid of MATLAB-SIMULINK models and solution of practical examples. The Moodle e-learning software is used for the final testing of students’ knowledge.

The final grade depends on the number of correctly answered questions of the final computer quiz prepared using the Moodle e-learning software. Student can obtain from 0 to 100 points in total. The 50 points is the minimum which corresponds with just half of correctly answered questions.

Lectures:
1. Introduction to the theory of signals.
2. Line codes.
3. Effect of the noise in baseband communication.
4. Modulations with harmonic carrier wave (AM, FM, PM).
5. Basic keying techniques (ASK, FSK, PSK).
6. Advanced keying techniques - part I (QPSK, O-QPSK, MSK, FFSK, GMSK).
7. Advanced keying techniques - part II (pi/4-DQPSK, 8PSK, MQAM, CAP).
8. Intersymbol interference and equalization of communication channel.
9. Pulse modulations - part I (PAM, PWM, PPM).
10. Pulse modulations - part II (PCM, DPCM, DM, ADM, SDM).
11. Multiplexing and multiple access.
12. Effect of the noise in bandpass communication and modulations in optoelectronic.
13. Introduction to the information theory and coding.

Computer excercises:
1. AWGN channel.
2. Matched filter and correlation receiver.
3. Basic keying techniques (ASK, FSK, PSK).
4. Principle of quadrature modulations (QPSK, 16QAM).
5. Pulse modulations (DM, ADM, SDM, PCM).
6. Spread-spectrum techniques.

Not applicable.

Give basic information about signals, methods, principles and parameters of communication systems, especially the digital systems, and also about negative effects on the bit error rate speed of transmission. To acquaint students with English terminology, lexicon, and specificity of English technical texts in the area of modern communication technologies using the set of lectures focused on the explanation of their principles.

All computer exercises are compulsory. Student must also pass the final computer quiz (see the criteria linked to learning outcomes).

Not applicable.

Not applicable.

HAYKIN S., MOHER M. Introduction to Analog & Digital Communications. 2nd ed. New Jersey (USA): John Wiley & Sons, 2007. (EN)
PROAKIS J. G. Digital Communications. 4th ed., New York (USA): McGraw-Hill, 2001. (EN)

GITLIN R. D., HAYES J. F., WEINSTEIN S. B. Data Communications Principles. New York (USA) : Plenum Press, 1992. 733 p. ISBN 0-306-43777-5 (EN)
HSU H. P. Schaum's Outline of Theory and Problems of Analog and Digital Communications. 2nd ed., New York (USA) : McGraw-Hill, 2003. 331 p. ISBN 0-07-140228-4 (EN)
SKLAR B. Digital Communications. 2nd ed. Upper Saddle River (USA): Prentice Hall, 2003. (EN)
XIONG F. Digital Modulation Techniques. 1st ed. Norwood (USA) : Artech House, 2000. 653 p. ISBN 0-89006-970-0 (EN)