Course detail

Autonomous Flying Systems

FSI-OASAcad. year: 2025/2026

In the frame of course there is introduced UAV technology in interactive form of education. Lectures are project oriented and during exercises there are composed groups of students, simple fixed UAV is integrated and in-flight tested by each group.

Lectures are covering – categorization and types of UAVs, typical missions and applications in civil area., sensors and types of payload for UAVs, autopilots, its concept, functionality and parameters, actuators (servos) and general other avionics for UAVs, regulation for operations, regulations and certification of vehicles, online test of operator.

Exercises – small fixed wing UAV assembly, avionics integration (remote control, autopilot, servos, power unit), mission planning and flight test. 

Language of instruction

Czech

Number of ECTS credits

3

Mode of study

Not applicable.

Guarantor

doc. Ing. Ivo Jebáček, Ph.D.

Department

Institute of Aerospace Engineering (LÚ)

Entry knowledge

Basic knowledge of Aerodynamics and Aircraft design

Rules for evaluation and completion of the course

Assembling a small autonomous system is a condition for proper completion of the course. Installation of the propulsion unit and necessary electronics, mission design, and functionality demonstration.

Aims

The course aims to familiarize students with autonomous systems, their equipment, and their operation. All in the form of a project.

Study aids

Not applicable.

Prerequisites and corequisites

Not applicable.

Basic literature

Hikmet Karakoc, Emre Özbek - Editors, Unmanned Aerial Vehicle Design and Technology, Springer Cham 2023, ISBN 978-3-031-45320-5 (EN)
Kimon P. Valavanis, George J. Vachtsevanos – Editors, Handbook of Unmanned Aerial Vehicles, Springer Dordrecht, 2015, ISBN 978-90-481-9707-1 (EN)

Recommended reading

Not applicable.

Classification of course in study plans

  • Programme N-LKT-P Master's

    specialization TLT , 1 year of study, summer semester, compulsory
    specialization STL , 1 year of study, summer semester, compulsory

Type of course unit

 

Lecture

26 hod., optionally

Teacher / Lecturer

doc. Ing. Ivo Jebáček, Ph.D.

Syllabus

  1. Introduction – UAS categories and terminology, typical applications.
  2. UAS operation regulation – category Open, Specific, Certified, ConOps, airspace for operation.
  3. Design and manufacturing regulations, certification.
  4. Preparation for test, online test for basic level UAV operator’s license.
  5. Fixed wing UAV exercise - drone assembly, airframe, servos, motors and accumulators.
  6. Sensors and typical payload for UAVs, data processing, data transfer, postprocessing.
  7. Remote control simulator, practices with DJI commercial multicopter drone.
  8. Autopilots – automatic control principles, types of autopilots related to UAvs categories
  9. PixHawk and ArduPilot introduction.
  10. Mission planner, mission preparation, data transfer.
  11. Fixed wing UAV exercise – 2nd step – integration of remote control receivers and autopilot, tuning.
  12. Flight tests with manual remote control
  13. Flight tests – stabilization and autonomous modes.

Exercise

11 hod., compulsory

Teacher / Lecturer

doc. Ing. Ivo Jebáček, Ph.D.

Syllabus

1. Characteristics of types of unmanned vehicles

2. Signs for determining UAS categories

3. Analysis of requirements for UAS construction

4. Tests for drone operator exams

5. Practical procedure for assembling a small drone

6. Practical flying on the simulator

7. Autopilot and its functions

8. Mission programming

9. Drone construction procedure

10. Practical flying with manual control

11. Flight tests - demonstration of functionality

Laboratory exercise

2 hod., compulsory

Teacher / Lecturer

doc. Ing. Ivo Jebáček, Ph.D.

Syllabus

1. Laboratory tests of drone control

2. Laboratory tests of electronic equipment and avionics of the drone