Detail publikace

Effect of powder milling on sintering behavior and monotonic and cyclic mechanical properties of Mo and Mo-Si lattices produced by direct ink writing

TKACHENKO, S. SLÁMEČKA, K. OLIVER URRUTIA, C. KSENZOVA, O. BEDNAŘÍKOVÁ, V. REMEŠOVÁ, M. DVOŘÁK, K. BALÁŽ, M. DEÁK, A. KACHLÍK, M. ČELKO, L. MONTUFAR JIMENEZ, E.

Originální název

Effect of powder milling on sintering behavior and monotonic and cyclic mechanical properties of Mo and Mo-Si lattices produced by direct ink writing

Typ

článek v časopise ve Web of Science, Jimp

Jazyk

angličtina

Originální abstrakt

Molybdenum is a refractory metal regarded as a promising basis for producing high-temperature components. However, the potential of manufacturing molybdenum-based structures by direct ink writing (DIW) has not been explored. In this study, three-dimensional porous molybdenum (Mo) and molybdenum-silicon (Mo-Si) composite lattices were fabricated using DIW with non-milled and milled powders. The effects of Mo powder morphology (resulting from milling) and chemical composition (alloying Mo with 3 and 10 wt% of Si) on the microstructure, phase composition, and static and cyclic compression properties at room temperature were investigated. Lattices fabricated from commercial spherical Mo powder exhibited the highest intra-filament porosity. Conversely, lattices fabricated from milled Mo powder were denser and had higher compressive strength, offset stress, and quasi-elastic gradient. Alloying Mo with Si during sintering resulted in composite lattices with Mo thorn Mo3Si microstructure. A low content of Mo3Si slightly decreased monotonic compression properties but did not affect the cyclic compression response compared to Mo lattices made from milled powder. In contrast, a high content of Mo3Si produced quasi-brittle lattices with reduced compressive strength and increased damage accumulation during cyclic loading. The cyclic behavior of all lattices was characterized by a ratcheting-dominated stress-strain response. Lattices fabricated from milled Mo and milled Mo-3 wt.%Si powders demonstrated superior performance compared to those fabricated from commercial spherical Mo and milled Mo-10 wt%Si powders. The results suggest that using milled powders can enhance the mechanical reliability and promote the use of DIW as preferred additive manufacturing technology for the fabrication of Mo-Si composite lattices. (c) 2023 The Authors. Published by Elsevier B.V. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/).

Klíčová slova

Robocasting; Molybdenum; Silicon; Porous structure; Metallic matrix composite; Cyclic compression test

Autoři

TKACHENKO, S.; SLÁMEČKA, K.; OLIVER URRUTIA, C.; KSENZOVA, O.; BEDNAŘÍKOVÁ, V.; REMEŠOVÁ, M.; DVOŘÁK, K.; BALÁŽ, M.; DEÁK, A.; KACHLÍK, M.; ČELKO, L.; MONTUFAR JIMENEZ, E.

Vydáno

5. 10. 2023

Nakladatel

Elsevier

Místo

AMSTERDAM

ISSN

2238-7854

Periodikum

Journal of Materials Research and Technology

Ročník

27

Číslo

10

Stát

Brazilská federativní republika

Strany od

2475

Strany do

2489

Strany počet

15

URL

https://www.sciencedirect.com/science/article/pii/S2238785423024511

Plný text v Digitální knihovně

http://hdl.handle.net/11012/244317

BibTex

@article{BUT187089,
  author="Serhii {Tkachenko} and Karel {Slámečka} and Carolina {Oliver Urrutia} and Olha {Ksenzova} and Vendula {Bednaříková} and Michaela {Remešová} and Karel {Dvořák} and Matej {Baláž} and Andréa {Deák} and Martin {Kachlík} and Ladislav {Čelko} and Edgar Benjamin {Montufar Jimenez}",
  title="Effect of powder milling on sintering behavior and monotonic and cyclic mechanical properties of Mo and Mo-Si lattices produced by direct ink writing",
  journal="Journal of Materials Research and Technology",
  year="2023",
  volume="27",
  number="10",
  pages="2475--2489",
  doi="10.1016/j.jmrt.2023.10.002",
  issn="2238-7854",
  url="https://www.sciencedirect.com/science/article/pii/S2238785423024511"
}